1.6. Each 58 000 km

Replacement of the air filter

You watch subsection 11.4.

Replacement of the fuel filter

You watch subsection 10.6.

Replacement of oil and the filter in the automatic transmission

Unscrewing of a stopper of discharge of oil from the automatic transmission

Arrangement of a stopper of discharge of oil from the hydrotransformer

Arrangement of bolts of fastening of the pallet of the automatic transmission

Removal of the mesh filter
 After unscrewing of tightening bolts (1) remove the mesh filter (2).

PERFORMANCE ORDER
1. Lift the car on the elevator.
2. For access to the transmission remove the lower mudguard.
3. Install the selector lever in situation P.
4. Carefully wipe the pallet of the automatic transmission.
5. Install the corresponding container under a drain stopper of the transmission, then unscrew a drain stopper and after running off of oil screw up a drain stopper on the place (see rice. Unscrewing of a stopper of discharge of oil from the automatic transmission).
6. For a bolt of fastening of a pulley of a bent shaft turn a bent shaft of the engine in such situation until the drain stopper of the hydrotransformer is seen through an opening in a transmission case (see rice. An arrangement of a stopper of discharge of oil from the hydrotransformer).
7. Install the corresponding container under a drain stopper гидротрансформато ра and unscrew a drain stopper. After full discharge of liquid from a hydrotransform a Torah establish a drain stopper into place.
8. Unscrew bolts of fastening of the pallet, then remove tightening levels and lower the pallet from the transmission (see rice. Arrangement of bolts of fastening of the pallet of the automatic transmission). Remove rubber laying.
9. Unscrew screws and remove the mesh filter (see rice. Removal of the mesh filter).
10. Clear the internal surface of the pallet of the automatic transmission.
11. Install the new mesh filter and fix by screws.
12. Install the pallet and tightening levels and fix the pallet by bolts, having tightened them the required moment.
13. In the presence establish a mudguard.
14. Lower the car on the earth, then release the lock lever and take the probe for measurement of level of oil in the automatic transmission.
15. Through a pipe for the probe of measurement of level of oil fill in 4 liters of the required liquid in the transmission. Start the engine in the idling mode with the selector lever in situation P.
16. Continue to add gradually liquid until its level is established 12 mm below than min tag on the probe for measurement of level of oil.
17. Move the selector lever to all provisions, detaining him in each situation for several seconds, then return the selector lever to situation P.
18. Repeatedly check liquid level in the automatic transmission.
19. Repeatedly add liquid min up to one level of 12 mm lower than a tag and move the selector lever to all provisions, then establish in situation P. Repeat this operation until liquid level in the transmission does not remain to constants.
20. Carry out a short trip and repeatedly measure liquid level in автоматичес which to the transmission.

Check of wear of overlays of a clutch plate

Template for check of wear of overlays of a clutch plate
 And = 55 mm;
In = 26 mm;
With = 7 mm;
D = 14 mm;
Е = 12 mm

Use of a template for check of wear of overlays of a clutch plate

1 – working cylinder of coupling;
2 – laying;
3 – pusher;
4 – template

Shooters showed two tags on a template.
In this provision of a template of an overlay of a clutch plate are in satisfactory condition.


Use of a template for check of wear of overlays of a clutch plate
Such provision of a template specifies that overlays of a clutch plate reached extreme wear.
The light arrow - a pusher moves with wear.
Dark arrow - a tag on a template.

PERFORMANCE ORDER
1. Check of wear of overlays of a clutch plate is made without removal of a clutch plate from the car.
2. Check can be executed from the lower party of the working cylinder of coupling and demands application of a special template which can be made of a metal strip (see rice. A template for check of wear of overlays of a clutch plate).
3. Lift a forward part of the car and record on supports.
4. Insert a template into a groove between a ledge of the working cylinder of coupling and a case.
5. Move a template against the stop until the end of a template contacts with a pusher of the working cylinder of coupling.
6. If two tags on a template are not seen, then overlays of a clutch plate are in satisfactory condition. If two tags on a template are seen, then overlays of a clutch plate reached extreme wear and the clutch plate needs to be replaced (see rice. Use of a template for check of wear of overlays of a clutch plate, Use of a template for check of wear of overlays of a clutch plate).
7. Remove a template and lower the car.