25.17. Screen wiper drive

Removal

Arrangement of the left and right consolidation at the basis of a windshield (1) and a partition of a motor compartment and the fan of a heater (2)

Removal of the plastic isolating panel located behind the accumulator

Detachment of the semicircular cover located at the screen wiper reducer basis

Removal of the panel from a forward part of a casing of the fan of a heater

Arrangement of screws of fastening of the isolating panel installed between the engine of a screen wiper and a casing of the fan of a heater

Removal of the isolating panel located between the engine of a screen wiper and a casing of the fan of a heater

Arrangement of a fixing bracket (1) and the screws (2) fixing side section of a casing of the fan of a heater

Arrangement of screws of fastening of the central section of a casing of the fan of a heater

Removal of the central section of a casing of the fan of a heater

Arrangement of nuts of fastening of the engine of a screen wiper

Release of the bracket of fastening located at the screen wiper engine basis

Detachment of the electric socket from the screen wiper block

Nut arrangement on a shaft of a crank (1) and bolts of fastening of the engine of a screen wiper

PERFORMANCE ORDER
1. Remove a weight wire from the accumulator.
2. Remove the screen wiper lever.
3. Open a cowl and establish it in vertical position. Include, and then switch off a screen wiper in order that the lever of a screen wiper was installed in a starting position. Remove rubber consolidation from the left and right side at the windshield basis. Remove rubber consolidation from the top part of a partition of a motor compartment and a cover of the fan of a heater (see rice. An arrangement of the left and right consolidation at the basis of a windshield and a partition of a motor compartment and the fan of a heater).
4. Remove the plastic isolating panel located behind the accumulator and disconnect the semicircular cover located at the screen wiper reducer basis (see rice. Removal of the plastic isolating panel located behind the accumulator, the Detachment of the semicircular cover located at the screen wiper reducer basis).
5. Release brackets of fastening and remove the panel from a forward part of a casing of the fan of a heater (see rice. Removal of the panel from a forward part of a casing of the fan of a heater).
6. Unscrew screws and remove the isolating panel located between the engine of a screen wiper and a casing of the fan of a heater (see rice. Arrangement of screws of fastening of the isolating panel installed between the engine of a screen wiper and a casing of the fan of a heater, Removal of the isolating panel located between the engine of a screen wiper and a casing of the fan of a heater).
7. Release fastening brackets, then unscrew screws and remove the left and right sections of a casing of the fan of a heater. For access to the engine of a screen wiper unscrew screws and remove the central section of a casing of the fan of a heater (see rice. Arrangement of a fixing bracket and the screws fixing side section of a casing of the fan of a heater, the Arrangement of screws of fastening of the central section of a casing of the fan of a heater, Removal of the central section of a casing of the fan of a heater).
8. Unscrew four nuts and disconnect a fastening bracket from the screen wiper engine basis (see rice. Arrangement of nuts of fastening of the engine of a screen wiper, Release of the bracket of fastening located at the screen wiper engine basis).
9. Take the screen wiper block, at the same time disconnect from it the electric socket (see rice. A detachment of the electric socket from the screen wiper block).
10. If necessary note a crank arrangement on an electric motor shaft, then unscrew a nut and remove a reducer from an electric motor shaft. Unscrew bolts of fastening of the electric motor and remove the engine from screen wiper knot (see rice. A nut arrangement on a shaft of a crank and bolts of fastening of the engine of a screen wiper).

Installation

PERFORMANCE ORDER
1. Installation is made in the sequence, the return to removal. Tighten bolts of fastening of the electric motor and a nut on a crank shaft the required moment. Check correctness of installation of all casings and panels of the fan of a heater and reliability of their fastening.