24.15.1. Removal


Removal of a protective film from the inside of a door

PERFORMANCE ORDER
1. Remove a door upholstery.
2. Being careful, remove a protective film from the inside of a door (see rice. Removal of a protective film from the inside of a door). If at removal the protective film is damaged, replace it.

Forward door on the Sedan and Station wagon models

Unscrewing of the nut fixing the window regulator lever to a glass guide

Door glass detachment from the ram of a guide and the back ram of a window regulator

PERFORMANCE ORDER
1. Lower glass down to an emphasis so that the nut of fastening of a guide of a window regulator was available through an aperture from the inside of a door, then remove a weight wire from the accumulator.
2. Unscrew the nut fixing the window regulator lever to a glass guide (see rice. Unscrewing of the nut fixing the window regulator lever to a glass guide).
3. Remove the forward lever of a window regulator from a glass guide, then lift a back part of glass and disconnect glass from the ram of a guide and the back ram of a window regulator (see rice. A door glass detachment from the ram of a guide and the back ram of a window regulator).
4. Being careful, lift glass and extract it from a door window up. If necessary, remove the ram from the lower part of a guide of glass.

Forward door on Coupet's models

PERFORMANCE ORDER
1. Lower glass down to an emphasis so that the nut of fastening of a guide of a window regulator was available through an aperture from the inside of a door, then remove a weight wire from the accumulator.
2. Unscrew the nut fixing the window regulator lever to a glass guide (see rice. Unscrewing of the nut fixing the window regulator lever to a glass guide).
3. Unscrew above and below screws of fastening of a forward guide of glass and take it from a door.
4. Weaken nuts of fastening of the holder of glass to a guide, then remove glass from a window regulator and take it through a door window up.

Window regulator of a forward door on the Sedan and Station wagon models

Unscrewing of screws of fastening of an electrical wiring to the window regulator engine

Arrangement of nuts of fastening of a window regulator

Extraction of a window regulator through an aperture from the inside of a door

PERFORMANCE ORDER
1. Lower glass down to an emphasis so that the nut of fastening of a guide of a window regulator was available through an aperture from the inside of a door, then remove a weight wire from the accumulator.
2. Unscrew the nut fixing the window regulator lever to a glass guide (see rice. Unscrewing of the nut fixing the window regulator lever to a glass guide).
3. Remove the forward lever of a window regulator from a glass guide, then lift a back part of glass and disconnect glass from the ram of a guide and the back ram of a window regulator (see rice. A door glass detachment from the ram of a guide and the back ram of a window regulator).
4. Lift glass against the stop up, then, using an adhesive tape, enshrine glass in this provision on a door.
5. On models with power windows note an arrangement of each wire, then unscrew screws and disconnect wires from the window regulator engine (see rice. Unscrewing of screws of fastening of an electrical wiring to the window regulator engine).
6. Unscrew the nuts and bolts fixing a window regulator and take a window regulator through an aperture of an internal part of a door, at the same time having released the top ram from a guide at doors (see rice. An arrangement of nuts of fastening of a window regulator, Extraction of a window regulator through an aperture from the inside of a door).

Window regulator of a forward door on Coupet's models

Prevention

At installation of a window regulator it is necessary to use the rivet gun and new rivets.

PERFORMANCE ORDER
1. Lower glass down to an emphasis so that the nut of fastening of a guide of a window regulator was available through an aperture from the inside of a door, then remove a weight wire from the accumulator.
2. Unscrew the nut fixing the window regulator lever to a glass guide (see rice. Unscrewing of the nut fixing the window regulator lever to a glass guide).
3. On models with power windows note an arrangement of each wire, then unscrew screws and disconnect wires from the window regulator engine.
4. Unscrew nuts of fastening of a guide, then remove glass from a window regulator and take it through a door window frame up.
5. Using a marker, note an arrangement of nuts of fastening of the lever of a window regulator on a door, then unscrew nuts.
6. Using a drill with a diameter of 6 mm, being careful, drill rivets of fastening of a window regulator to a door.
7. Take a window regulator through an aperture from the inside of a door.

Back door on the Sedan and Station wagon models

Removal of a sealant of glass from a door window frame

Unscrewing of the top screw of fastening of a back guide of glass

Unscrewing of the lower bolt of fastening of a back guide of glass

Removal of a back guide of glass from a door

Glass guide detachment from a window regulator

Removal of glass of a back door through a door window frame

PERFORMANCE ORDER
1. Lower glass so that the guide was available through an aperture from the inside of a door, then remove a weight wire from the accumulator.
2. Being careful, remove a sealant of glass and take it from a door window frame (see rice. Removal of a sealant of glass from a door window frame).
3. Unscrew the bolt located in the lower part and the screw located in the top part of fastening of the directing back part of glass. Move a guide down and take it from a door (see rice. Unscrewing of the top screw of fastening of a back guide of glass, Unscrewing of the lower bolt of fastening of a back guide of glass, Removal of a back guide of glass from a door).
4. Turn glass and disconnect a glass guide from a window regulator, then lift glass up and take it from a door window frame (see rice. A glass guide detachment from a window regulator, Removal of glass of a back door through a door window frame).

Back side glass on Coupet's models

PERFORMANCE ORDER
1. Remove an inertial drum of a seat belt of a front seat.
2. Remove the top consolidation of glass from a body.
3. Being careful, remove a protective film from a body for access to a window regulator and glass. At damage of a protective film it needs to be replaced.
4. Lower glass in such situation that nuts of fastening of glass to a window regulator were available through doorways.
5. Unscrew nuts of fastening of glass to a window regulator and remove glass from the car.

Window regulators of a back door on the Sedan and Station wagon models

Unscrewing of screws of fastening of an electrical wiring to the window regulator engine

Arrangement of nuts and bolt of fastening of a window regulator to a door

Extraction of a window regulator through an aperture from the inside of a door

PERFORMANCE ORDER
1. Lower glass in such situation that access to a guide of glass was possible through a doorway, then remove a weight wire from the accumulator.
2. Incline glass at doors and remove a glass guide from the window regulator lever. Lift glass against the stop up and, using an adhesive tape, record it in this situation.
3. On models with power windows note an arrangement of each wire, then unscrew screws and remove wires from the window regulator engine (see rice. Unscrewing of screws of fastening of an electrical wiring to the window regulator engine).
4. Unscrew a bolt and nuts of fastening of a window regulator and take a window regulator through an aperture from the inside of a door (see rice. An arrangement of nuts and a bolt of fastening of a window regulator to a door, Extraction of a window regulator through an aperture from the inside of a door).

Window regulator of back side glass on Coupet's models

PERFORMANCE ORDER
1. Remove back side glass from a body.
2. For access to a window regulator unscrew screws and remove the support plate from a body.
3. Uncover a back part of the switch of a window regulator. Note an arrangement of each wire and disconnect window regulator engine wires from the switch. Take a plait of wires from fastening brackets so that it could be removed together with a window regulator.
4. Unscrew bolts and remove an assembly plate of an armrest from a body.
5. Being careful, remove a back part of a molding and a cap for access to nuts of fastening of a window regulator.
6. Unscrew nuts and remove a window regulator from the car.